Product Details:
Power Supply | Power supply to the RS - 232 port (TXD,RTS or DTR) |
Working Environment | -20degC to 70degC,5% to 95% relative humidity |
Product Appearance | Plastic shell 63mmx33mmx17mm |
Isolation | 2500V in succession or 7500V pulse |
Electric Interface | RS-232 |
Transmission Speed | 0-57.6kbps |
Working Mode | Asynchronous full duplex |
Interface Feature | Conform to EIA RS - 232 and CCITT v. 24 asynchronous protocol |
The ATC-131 optically isolates and protects the transmit and receive lines of your RS-232 port from ground loops and power surges up to 2500V RMS for one minute. The data stream is converted from an electrical pulse to an optical beam, then back to an electrical pulse. Because there is no electrical connection between the DTE and DCE sides of the isolator, the ATC-131, unlike a surge suppressor, will not pass large sustained power surges through to your equipment.
This isolator will protect both the transmit and receive lines at baud rates up to 57.6K without the need of an external power supply. Power is derived through the transmit and handshake lines. Special circuitry allows the ATC-131 to be powered regardless of the state of the handshake lines. At least one handshake line must be connected on each side of the isolator. Note that handshake line signals are not passed through the isolator.
Features:
Product Details:
Power Supply | Power supply to the RS - 232 port |
Distance | 24AWG lead for 12KM @600BPS,24AWG lead for 1KM @38.4KBPS,24AWG lead for 100M @57.6KBPS |
Interface Feature | One port conforms to EIA RS-232 and CCITT V.24 the other uses special 4-core cooper wire |
Connector | One side of RS-232 uses DB9 hole connector,The circuit side uses DB9 pin connector |
Transmission Mode | Asynchronous,full duplex or simplex |
Isolation | 2500V in succession or 7500V pulse |
Transmission Speed | 0-57.6kbps |
Working Environment | -20degC to 70degC,5% to 95% relative humidity |
Product Appearance | Plastic shell 63mmx33mmx17mm |
ATC - 155, RS - 232 photoelectric isolation line drives or line transceiver or line repeater insulation. It can be in optical isolation and make two equipment for asynchronous communication of RS - 232 communication distance is increased to 12 km at the same time.
Due to adopt photoelectric isolated technology, completely isolated RS - 232 devices on both ends of the electric and ground wire loop, so as to protect communications equipment from the power supply ground loop interference and surge damage, significantly improve the stability and reliability of communication system. Due to the changed the RS - 232 interface way of single side transmission, using the double balance transfer, greatly increase the communication distance. In the use of dedicated line of asynchronous point-to-point RS - 232 field, ATC - 155 can be used to meet the needs of interface protection or extended distance.
ATC - 155 volume small, the wire has no special requirement, don't need an external power supply, can be directly inserted to the device of the RS - 232 interface, use very convenient.
Features:
Product Details:
Interface Feature | Compatible with EIA/TIA RS-232C,RS-485/RS-42 (2-Wire Half Duplex or 4-wire full Duplex |
Supply | External 9-12VDC |
Transmission Distance | 0-5 Kilometers (115200-9600BPS) |
Working Environment | -25degC-70degC,5%-95%RH |
Size | 125 mm x 54 mm x 25 mm |
Electrical Interface | RS-232C-DB9 Female Connector;RS-422/RS-485-4 bit Terminal |
Transmission Media | Twisted pair cable or shielded cable |
Operation Mode | Asynchronous half or full duplex |
Signal Indication | 3 light indication TR,RD,PWR |
Isolation | 3500VRMS 500VDC sequence |
Transmission Speed | 9600BPS to 115.2 KBPS |
ATC-105 Isolation Interface Converter is compatible with RS-232C, RS-422, RS-485 standards and capable of converting single end RS-232 signal into RS-422 or RS-485 signal of balanced signal. The built in photoelectric isolator can offer 3500V isolation voltage and the rapid Transient Voltage Suppressor (TVS) can effectively inhibit lightning and ESD, prevent lightning strike and common code interference.
Connect PC, IPC, or portable computer via a DB9 female connector at RS-232 interface, and connect RS-422, RS-485 end via convenient 4-bit terminal. The RS-485 supports dual-line half duplex. The inner circuit of ATC-105 Photoelectric Isolation Interface Converter can detect data direction and switch to control it automatically, conveniently to form a RS-485 network without any shake hand signal. This kind of RS-485 control is fully transparent and need no software amendment for the former working modes basing on RS-232.
ATC-105 Photoelectric Isolation Interface Converter can provide credible connection for point to point, point to multi-point communication. The point to multi-point allows connecting 128 RS-422 or RS-485 interface devices with data transmission speed of 0-115.2KBPS. The 3 power supply and data flow indication light can indicate malfunction. It supports communication modes including RS-232C to RS-422, RS-232 to RS-485 conversion.
Features:
Product Details:
Transmission Media | Twisted pair cable or shielded cable |
Size | 95 mm x 85 mm x 26 mm |
Operation Mode | Asynchronous half or full duplex |
Signal Indication | 3 light indication TR,RD,PWR |
Protection Grade | 1000 W RS-485/RS-232 Side,600 W RS-232 Side |
Isolation | Isolation Voltage 3500VRMS 500VDC sequence |
Transmission Speed | 9600BPS to 5 KM |
Supply | External 9-12VDC |
Transmission Distance | 0-5 Kilometers (115200-9600BPS) |
Working Environment | -25degC-70degC,5%-95%RH |
Connect PC, IPC, or portable computer via a DB9 female connector at RS-232 interface, and connect RS-422, RS-485 end via convenient 4-bit terminal. The RS-485 supports dual-line half duplex. The inner circuit of ATC-105 Photoelectric Isolation Interface Converter can detect data direction and switch to control it automatically, conveniently to form a RS-485 network without any shake hand signal. This kind of RS-485 control is fully transparent and need no software amendment for the former working modes basing on RS-232.
ATC-107N Photoelectric Isolation Interface Converter can provide credible connection for point to point, point to multi-point communication. The point to multi-point allows connecting 256 RS-422 or RS-485 interface devices with data transmission speed of 0-115.2KBPS. The 3 power supply and data flow indication light can indicate malfunction. It supports communication modes including RS-232C to RS-422, RS-232 to RS-485 conversion.
Product Details:
Transmission Media | Twisted pair cable or shielded cable |
Connector | RS-232 - DB9 Female; RS-485 - DB9 Male & Terminal Block Connector |
Operation Mode | Asynchronous half duplex |
Transmission Speed | 9600BPS to 6000 feet |
Supply | Port Powered (It Takes power +- 5.5 V form TD or Handshake Lines.) |
Working Env | 0degC-50degC,5%-95%RH |
Product Details:
Transmission Media | Twisted pair cable or shielded cable |
Connector | RS-232 - DB9 Female; RS-485 - DB9 Male & Terminal Block Connector |
Operation Mode | Asynchronous half duplex |
Transmission Speed | 9600BPS to 6000 feet |
Supply | Port Powered (It Takes power +- 5.5 V form TD or Handshake Lines.) |
Working Environment | 0degC-50degC,5%-95%RH |
Product Details:
Transmission Media | Twisted pair cable or shielded cable |
Connector | DCE Side - DB 9 Female & DTE Side - DB 9 Male |
Isolation | 2500V RMS Optical Isolation |
Supply | Port Powered |
Working Environment | 0degC-50degC,5%-95%RH |
Product Details:
Storage Temperature | -40 ~ 85degC (-40 ~ 176degF) |
Weight | 0.45Kg |
Dimension | 88mmx33mmx17mm |
Baud Rate | 300-115.2kbps automatic detection rate of serial port signals |
Interface | Compatible with the EIA/TIA RS-232-C and TTL/CMOS standard RS-232 TD,RD,GND |
Transmission Distance | TTL side 10 meters (19.2 kbps) |
Housing | Plastic shell |
Ambient Relative Humidity | 5% to 95%(non-condensing) |
Operating Temperature | -20 ~ 70degC (-4 ~ 158degF) |
Features:
Product Details:
Computer Interface | 3 in 1 (4-Port) RS -232/RS-422/RS-485 Interface |
Transmission Rate | 230KBPS serial interface and 10/100 MBPS Ethernet |
Signal Indication | LINK (Indicate Ethernet link),ACT (Sending / Receiving data serial to Ethernet),PWR |
Supply | 9-24VDC |
Working Environment | 0degC-70degC,10%-95%RH |
Product Details:
Computer Interface | 3 in 1 RS-232/RS-422/RS-485 interface |
Transmission Rate | 230KBPS serial Interface and 10/100 MBPS Ethernet |
Signal Indication | LINK (Indicate Ethernet link),ACT (Sending / Receiving data serial to Ethernet),PWR |
Supply | 9-24VDC |
Working Environment | 0degC-70degC,10%-95%RH |
Product Details:
Computer Interface | 3 in 1 RS-232/RS-422/RS-485 interface |
Support | Windows 95/98/ME/NT/2000/XP/2003/WIN7/WIN8/WIN10 |
Transmission Rate | 230KBPS serial interface and 10/100 MBPS |
Signal Indication | Link (Indicate Ethernet link),PWR (Power Indication) ACT Sending / Receiving data serial to Ethernet |
Supply | 9-24VDC |
Working Env | 0degC-70degC,10%-95%RH |
The ATC-1000 is a RS232/RS485 to TCP/IP converter integrated with a robust system and network management features designed for industrial equipment to be accessed and controlled via Intranet or Internet. By integrating RTOS (Real Time Operating System) and complete TCP/IP protocol stack capability, ATC’s ATC-1000 provides not only a robust and high performance system to make your device connecting to Network, but also ease installation and Internet access. The ATC-1000 Web Configurator is a breeze to operate and totally independent of the operating system platform you use.
Features:
Product Details:
Computer Interface | USB V1.1/2.0 Plug and Play |
Working Environment | 0degC-70degC,10%-95%RH |
Size | 105 mm X 85 mm X 27 mm |
Field Interfaces | RS-232,RS-422,RS-485 (Half Duplex) |
Support | Windows 98/ME/XP/2000/CE,MAC & Linux |
Field Interface | Half duplex (Dual Buses) |
Isolation | Isolation Voltage 3500VRMS 500VDC sequence |
Transmission Rate | 300BPS to 1MBPS |
Signal Indication | Sending data(red) and receiving data (green) LED |
Supply | From the USB port |
Bus Protection | 600W |
Product Details:
Computer Interface | USB V1.1/2.0 Plug and Play |
Field Interface | 4 Port RS-232 |
Support | Windows 98/ME/XP/2000/CE,MAC & Linux |
Transmission Rate | 300BPS to 460.8 KBPS |
Supply | From the USB port or external power |
Bus Protection | 600W |
Working Environment | 0degC-70degC,10%-95%RH |
Consumption | Less than 300 mA |
Operating Environment | -40 to 70degC,10 to 90%relative humidity,non-condensing |
Product Details:
Interface | Rs-232/RS485/RS422 |
Transmission Power | Less than 800 Mw |
Carrier Frequency | 433 MHz |
Interface Speed Rate | 1.2 ~ 38.4 KBPS |
Transmission Distance | 2000 mtr |
Support | Windows 98/ME/XP/2000/CE,MAC & Linux |
Signal Indication | TXD,RXD,PWR |
Supply | 9-12 VDC |
Working Environment | -20degC-65degC,10%-90%RH |
75 wireless digital transmission module offers standard RS-232, RS-485 and UART/TTL level interfaces for direct connection with computers, use's RS-485 equipments, SCM or other UART parts. ATC-875 has adopted half duplex communication channel most suitable for point to multi-point communication mode. The primary station takes full control of communication harmony, and adopts data frames with address codes for data or command transmitting. The secondary station shall fully receive them and select response by comparing address codes; all the work shall be fulfilled by upper layer protocols, which shall ensure that only one wireless module in the communication network is in the transmitting state in any instant to avoid mutual interference. Therefore, the transmission channel built by ATC-875 is transparent to the user. ATC-875 can also be applied to point to point communication, making it easier and smoothly upgrade wire (RS232/485/TTL) transmission mode in original system.
Product Details:
Interface | Rs-232/RS485/RS422 |
Transmission Power | Less than 500 Mw |
Carrier Frequency | 433 MHz |
Interface Speed Rate | 1.2 ~ 38.4 KBPS |
Transmission Distance | 800 mtr |
Support | Windows 98/ME/XP/2000/CE,MAC & Linux |
Signal Indication | TXD,RXD,PWR |
Supply | 9-12 VDC |
Working Environment | -20degC-65degC,10%-90%RH |
Product Details:
Interface | Rs-232/RS485/RS422 |
Transmission Power | Less than 100 Mw (ATC-863 & ATC-871) |
Carrier Frequency | 433 MHz |
Interface Speed Rate | 1.2 ~ 38.4 KBPS |
Transmission Distance | 500 mtr |
Support | Windows 98/ME/XP/2000/CE,MAC & Linux |
Signal Indication | TXD,RXD,PWR |
Supply | 9-12 VDC |
Working Environment | -20degC-65degC,10%-90%RH |
Product Details:
Computer Interface | 3 in 1 RS-232/RS-422/RS- 485 interface |
Support | Ad-Hoc,Infrastructure,pseudo IBSS mode support |
Transmission Rate | Auto negotiating 10/100 MBPS Ethernet |
Signal Indication | LINK (Indicate WLAN),DIS (Indicate WLAN status) ACT (Transmit data serial to WLAN),PWR |
Supply | 9-36VDC |
Range | 1000ft. (Open Environment) |
Working Environment | 0degC-55degC,95%RH |
Product Details:
Interface | Rs-232/RS485/RS422 |
Transmission Power | Less than 100 Mw (ATC-863 & ATC-871)less than 500 MW (ATC-873) |
Carrier Frequency | 2.4 GHz ISM Band (Complete IEEE 802.15.4 spec compliant) |
Interface Speed Rate | Maximum up to 115.2 KBPS |
Transmission Distance | 500 mtr. @ 12 dbm/PA & - 102 dbm/LNA |
Support | Windows 98/ME/XP/2000/CE,MAC & Linux |
Signal Indication | TXD,RXD,PWR |
Supply | 9-12 VDC |
Working Environment | -20degC-65degC,10%-90%RH |
Product Details:
Dimension | 6.3" L x 4.3" W x 1.25" H |
Interface | SC or ST |
Fiber Requirements | 50/125um,100/140um,200um |
Transmission Distance | SM20 km,MM2km |
Wavelength | SM1310 nm,MM850 nm |
Coupled Power Budget | 12.1 dB |
Point to Point Transmission | Half-duplex and full-duplex |
2.RS-232/485/422 Port
3. Physical Specifications:
Product Details:
Computer Interface | USB V1.1/2.0 Plug and Play |
Support | Windows 98/ME/XP/2000/CE,MAC & Linux |
Transmission Rate | Over 460 KBPS |
Signal Indication | Sending data(red) and receiving data(green) LED |
Supply | From the USB port |
Bus Protection | 600W |
Working Env | 0degC-70degC,10%-95%RH |
System Requirements:
Product Details:
Bus Protection | 600W |
Computer Interface | USB V1.1/2.0 Plug and Play |
Consumption | Less than 100 mA |
Signal Indication | Sending data(red) and receiving data(green) LED |
Supply | From the USB port |
Support | Windows 98/ME/XP/2000/CE,MAC & Linux |
Transmission Rate | From 300 bps to 1Mbps |
Working Environment | 0 to 70degC,10 to 90% relative humidity,non-condensing. |
Product Details:
Interface Feature | Interface is compatible with EIA/TIA RS-485/RS-422 standard |
Product Appearance | 100mmx86mmx26mm |
Electric Interface | RS-422/RS-485 interfaces are 6-bit screw terminal |
Transmission Media | Twisted-pair cable or shielded cable |
Working Mode | Asynchronous half or full duplex |
Signal Indication | 3 signal indication lights indicate TXD,RXD and PWR |
Isolation | Isolation voltage 3500VRMS 500VDC sequence |
Transmission Speed | 0-115.2kbps |
Transmission Distance | 0-5 km |
Working Environment | -20degC to 70degC,5% to 95% relative humidity |
ATC-109N data repeater is a kind of data relay communication product of photoelectric isolated RS-422/RS-485. It can be used with ATC-108 Photoelectric Isolation Interface Converter in combination. ATC-109N data repeater can prolong the communication distance of RS-422 /RS-485 bus network and increase the number of RS-422/RS-485 bus network devices.
The inner circuit of ATC-109N Photoelectric Isolation Data Repeater can detect data direction and switch to control it automatically, conveniently to form a RS-485 network without any shake hand signal. This kind of RS-485 control is fully transparent and need not amend software for the former network basing on RS-422/485 working modes. The built in photoelectric isolator and DC/DC converter can offer 3500V isolation voltage and the rapid Transient Voltage Suppressor (TVS) can effectively inhibit lightning and ESD, provide 1000W lightning strike and surge protection power on each line, and prevent lightning strike and common code interference.
Product Details:
AC DC Power Adaptor | +5V DC,1A EMI and Safety CE,FCC ClassA |
Dimensions | 95 mm (L)*71 mm (W) *26 mm (H) |
EMI and Safety | CE,FCC Class A |
External Power Supply | AC 86~260V 50~60Hz |
Fiber Interface | SC/PC Fiber Connector,9/125um Single Mode Fiber SC/PC or ST/PC Fiber Connector,50/125 or 62.5/125 |
Humidity | 5%~90% (Non-condensing) |
Product Details:
Computer Interface | USB V1.1 2.0 Plug and Play |
Transmission Rate | From 300 bps to 1Mbps |
Power | From the USB port |
Consumption | Less than 100 mA |
Logic Protection | 600W |
ABS Enclosure | 55 x 35 x 15 mm(not include cable) |
Operating Environment | 0 to 70degC, 10 to 90% relative humidity, non-condensing |
Product Details:
Computer Interface | USB 1.1 2.0 Plug and Play |
Operating Environment | 0 to 70degC,10 to 90% relative humidity,non-condensing. |
Field Interfaces | RS-422 Full Duplex,Automatic flow control for RS422 Full Duplex. |
Transmission Rate | From 300 bps to 1Mbps |
Length | 1200 m |
Consumption | Less than 100 mA |
Bus Protection | 600W |
USB Connection | Mini-B connector. 100mm cable with the module. |
Connector | DB 9Male |
ABS Enclosure | 60 x 57 x 24 mm(not include cable) |
Product Details:
Weight | 0.8 kg (1.32lb) |
Dimensions | 54 x 105 x 135 mm (2.1 x 4.1 x 5.3 in) |
Interface | Ethernet 10Base-T or 100Base-TX |
Input Voltage | 8-24 VDC@500mA |
Operating Temperature | e -40deg to 70degC |
Connector | RJ45 Removable Terminal Block |
Protocol | Port based,MAC address,VID,VLAN priority,IPv4 ToS,IPv6 DSCP,TCP/UDP a |
Technology Standards | IEEE802.3,802.3u,802.3x,IEEE 802.1x,IEEE 802.1Q |
Address Table Size | 2K MAC Addresses |
Performance | 10/100BaseT(X) auto negotiation speed,F/H duplex mode,and auto MDI/MDIX connection |
Installation | DIN-Rail Mounting |
Product Details:
Pitch | 1.27mm |
Dimensions | 37x27x12mm |
Protocols | TCP,UDP,HTTP,Telnet,IP,ICMP,ARP |
IP Addressing | DHCP,Static IP |
Baud | 300 to 230,400 bps |
Data Bits | 7,8 |
Operation Modes:
General:
Product Details:
Coupled Power Budget | 12.1 dB |
Fiber Requirements | 50/125um,100/140um,200um |
Interface | SC or ST |
Point to Point Transmission | Half-duplex and full-duplex |
Transmission Distance | SM20 km,MM2km |
Wavelength | SM1310 nm,MM850 nm |
RS-232/485/422 Port
Physical Specifications:
Product Details:
Data Rate | 1200bps-115200bps |
Stop Bits | 7,8 bits |
Frequency Range | GSM 850/ 900 /1800 /1900 MHz |
Weight | 0.5 kg |
Housing | Iron (1mm) |
Humidity | 5 to 95% |
Product Details:
Computer Interface | 3-in-1 RS-232/422/485 interface Max.230Kbps Serial interface and 10/100 Mbps Ethernet(Auto sensing) |
Data Rates | 1200 bps to 230,400 bps |
Signal Indication | 10/100Base-TX Link,Date Sending / Receiving between Serial and the Ethernet PWR(Power Indication) |
CPU | 16-bit x86 Embedded CPU |
Memory | 512 Kbytes Flash,512Kbytes SDRAM,512Kbytes EEPROM |
Input Voltage | 8-24 VDC@500mA |
Dimension | 95 x 65 x 25 mm - Din Rail Mounting |